How to Set up a Tub: Install an Acrylic Bathtub and Also Tub Surround
How to Set up a Tub: Install an Acrylic Bathtub and Also Tub Surround
Blog Article
Just about everyone maintains their private perception in relation to Tools You Need to Install a New Bathtub .
Setting up a bath tub isn't precisely brain surgery, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old bathtub is readily available, the job can move immediately; if you have to open up a wall surface to eliminate the old bathtub as well as place the new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly require an assistant to leave the old tub as well as set in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed job, it is far better to think about using one prior to you begin. Possibilities are you might require a specialist plumber to make tube connections.
This post will assist you mount a new bath tub in your bathroom if you have currently bought a brand-new bathtub and don't require to transform the setup of your previous water supply pipes.
Your devices and also product checklist ought to make up the following:
Getting ready for the Setup
To start with, the sustaining structure provided with the bath should be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of eliminating the existing faucets can be rather problematic because of the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleaned of any type of old securing substance.
Prior to moving on to fit the brand-new taps, compare the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Using the two wood boards under its feet, position the bathtub in the required setting. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next goal is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the spirit level checks out degree.
To mount taps, fit the bottom of the outermost adaptable faucet connector to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water and inspect all joints and also new pipework for leaks as well as tighten them if necessary. Fill the tub as well as also inspect the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub ought to wait up until the bath tub has been used a minimum of when as this will certainly resolve it into its final setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Protect the faucet in place with the producer supplied backnut. As soon as the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular tap adapters. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, causing the water to pass through the wall surface in between the bath and the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub remains in usage. The sealer can break rather very early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a reader on How to Install a Bathtub, I was thinking sharing that piece of writing was sensible. Are you aware of anybody else who is interested in the topic? Why not promote it. Thank you so much for going through it.
Additional Resources
Report this page